Linksys Network Router WAG120N User Manual

USER GUIDE  
Wireless ADSL2+ Modem Router  
Models: WAG120N, WAG160N v2, WAG320N  
 
Table of Contents  
Wireless ADSL2+ Modem Router  
ii  
 
Product Overview  
Chapter 1  
USB (WAG320N only) (Green) The USB LED  
lights up when a USB device is connected to the  
Modem Router through the USB port.  
Chapter 1:  
Product Overview  
Thank you for choosing the Wireless ADSL2+ Modem  
Router. This device lets you access the Internet via a  
wireless connection or through one of its four switched  
ports. You can also use it to share resources such as  
computers, printers and files. A variety of security features,  
such as WPA2security, a Stateful Packet Inspection (SPI)  
firewall and NAT technology, help to protect your data  
and your privacy while online. Configuration is easy using  
the provided browser-based utility.  
Wireless (Green) The Wireless LED lights up  
when the wireless feature is enabled. It flashes  
when the Modem Router is actively sending or  
receiving data over the network.  
DSL (Green) The DSL LED lights up whenever  
there is a successful DSL connection. The LED  
flashes green while the Modem Router is  
establishing the ADSL connection.  
Internet (Green/Red) The Internet LED lights up  
green and stays on when a connection is made  
through the Internet port. It flashes to indicate  
network activity over the Internet port. The LED  
is lit red when an authentication error occurs.  
Front Panel  
Back Panel  
Power (WAG120N: Green/Amber; WAG160N v2  
and WAG320N: Green/Red) The Power LED  
is continuously lit green while the device is  
powered on. The LED is lit amber (WAG120N)  
or red (WAG160N v2 and WAG320N) if a POST  
(Power On Self Test) failure or device malfunction  
occurs.  
DSL The DSL port connects to the ADSL line.  
Ethernet 4, 3, 2, 1 The Ethernet ports (4, 3, 2, 1)  
connect the Modem Router to wired computers  
and other Ethernet network devices.  
Ethernet 1-4 (Green) These numbered LEDs,  
one for each of the numbered ports on the  
Modem Router’s back panel, serve two purposes.  
If the LED is continuously lit, the Modem Router is  
successfully connected to a device through that  
port. It flashes to indicate network activity over  
that port.  
NOTE: The Ethernet  
1
port can  
also be configured as the WAN  
port. To do this, access the Web-  
based utility (refer to “Chapter 3:  
then select the Setup > Ethernet tab.  
NOTE: The Ethernet 1 LED is lit amber  
when the WAN link is established on that  
port.  
USB (WAG320N only) The USB port connects  
the Modem Router to a hard drive or flash-  
based USB storage device.  
Wi-Fi Protected Setup™ Button (WAG120N:  
Green/Amber; WAG160N v2 and WAG320N:  
Green) Press this button to have Wi-Fi Protected  
Setupsearch for your Wi-Fi Protected  
Setup™-supported wireless device. The LED is  
continuously lit green when a Wi-Fi Protected  
Setup™ connection is successfully established.  
The LED blinks slowly while Wi-Fi Protected  
Setup™ is setting up a connection, and is lit amber  
(WAG120N) or blinks rapidly (WAG160N v2 and  
WAG320N) if an error occurs. The LED is off when  
Wi-Fi Protected Setup™ is idle.  
Reset There are two ways to reset the Modem  
Router’s factory defaults. Either press and  
hold the Reset button for approximately five  
seconds, or restore the defaults from the  
Administration > Factory Defaults screen of the  
Modem Router’s web-based utility.  
Power The Power port is where you will connect  
the power adapter.  
On/Off Button Press the On/Off button to turn  
power to the device on or off.  
NOTE: Wi-Fi Protected Setup™ is a feature  
that makes it easy to configure your  
wireless network and its security settings.  
Wireless ADSL2+ Modem Router  
1
 
 
Product Overview  
Chapter 1  
Follow these instructions:  
Placement Positions  
There are two ways to physically install the device. The  
first way is to place the device horizontally on a surface.  
The second way is to mount the device on a wall.  
1. Determine where you want to mount the device. Make  
sure that the wall you use is smooth, flat, dry, and  
sturdy. Also make sure the location is within reach of  
an electrical outlet.  
The best place for the device is usually at the center of  
your wireless network, within range of all of your wireless  
devices.  
2. Drill two holes into the wall. Make sure the holes are  
152 mm (6 inches) apart.  
3. Insert a screw into each hole and leave 3 mm  
(0,12 inches) of its head exposed.  
Horizontal Placement  
The device has four rubber feet on its bottom panel. Place  
the device on a level surface near an electrical outlet.  
4. Maneuver the device so the wall-mount slots line up  
with the two screws.  
5. Place the wall-mount slots over the screws and slide  
the device down until the screws fit snugly into the  
wall-mount slots.  
Wall-Mounting Placement  
The device has two wall-mount slots on its bottom  
panel. The distance between the slots is 152 mm  
(6 inches).  
Two screws are needed to mount the device.  
Suggested Mounting Hardware  
4-5 mm  
1-1,5 mm  
Note: Mounting hardware illustrations are not  
true to scale.  
NOTE: Cisco is not responsible for damages  
incurred by insecure wall-mounting hardware.  
152 mm  
Wall Mounting Template  
Wireless ADSL2+ Modem Router  
2
 
 
Wireless Security Checklist  
Chapter 2  
Chapter 2:  
4. Enable encryption  
Wireless Security Checklist  
Encryption protects data transmitted over a wireless  
network. Wi-Fi Protected Access(WPA/WPA2) and  
Wired Equivalency Privacy (WEP) offer different levels of  
security for wireless communication.  
Wireless networks are convenient and easy to install, so  
homes with high-speed Internet access are adopting them  
at a rapid pace. Because wireless networking operates by  
sending information over radio waves, it can be more  
vulnerable to intruders than a traditional wired network.  
Like signals from your cellular or cordless phones, signals  
from your wireless network can also be intercepted. Since  
you cannot physically prevent someone from connecting  
to your wireless network, you need to take some additional  
steps to keep your network secure.  
A
network encrypted with WPA/WPA2is more  
secure than a network encrypted with WEP, because  
WPA/WPA2uses dynamic key encryption. To protect  
the information as it passes over the airwaves, you should  
enable the highest level of encryption supported by your  
network equipment.  
WEP is an older encryption standard and may be the  
only option available on some older devices that do not  
support WPA.  
1. Change the default wireless  
network name or SSID  
General Network Security Guidelines  
Wireless network security is useless if the underlying  
network is not secure.  
Wireless devices have a default wireless network name  
or Service Set Identifier (SSID) set by the factory. This is  
the name of your wireless network, and can be up to 32  
characters in length. Linksys by Cisco wireless products  
use linksys as the default wireless network name. You  
should change the wireless network name to something  
unique to distinguish your wireless network from other  
wireless networks that may exist around you, but do not  
use personal information (such as your Social Security  
number) because this information may be available for  
anyone to see when browsing for wireless networks.  
Password protect all computers on the network and  
individually password protect sensitive files.  
Change passwords on a regular basis.  
Install anti-virus software and personal firewall  
software.  
Disable file sharing (peer-to-peer). Some applications  
may open file sharing without your consent and/or  
knowledge.  
2. Change the default password  
Additional Security Tips  
For wireless products such as access points, routers, and  
modem routers, you will be asked for a password when  
you want to change their settings. These devices have a  
default password set by the factory. The default password  
is admin. Hackers know these defaults and may try to  
use them to access your wireless device and change your  
network settings. To thwart any unauthorized changes,  
customize the device’s password so it will be hard to  
guess.  
Keep wireless routers, access points, or modem routers  
away from exterior walls and windows.  
Turn wireless routers, access points, or modem routers  
off when they are not being used (at night, during  
vacations).  
Usestrongpassphrasesthatareatleasteightcharacters  
in length. Combine letters and numbers to avoid using  
standard words that can be found in the dictionary.  
3. Enable MAC address filtering  
WEB:Formoreinformationonwirelesssecurity,  
Linksys by Cisco routers and modem routers give you  
the ability to enable Media Access Control (MAC) address  
filtering. The MAC address is a unique series of numbers  
and letters assigned to every networking device. With  
MAC address filtering enabled, wireless network access  
is provided solely for wireless devices with specific MAC  
addresses. For example, you can specify the MAC address  
of each computer in your home so that only those  
computers can access your wireless network.  
Wireless ADSL2+ Modem Router  
3
 
 
Advanced Configuration  
Chapter 3  
List of Screens in the Utility  
The screens are organized hierarchically as listed below.  
(Some screens may not apply to all models.)  
Chapter 3:  
Advanced Configuration  
After you finish running the Setup Wizard on the Setup  
CD-ROM, the device is ready for use.To change the device’s  
advanced settings, access the Configuration Utility via a  
web browser on a computer connected to the device.  
NOTE FOR USERS IN NEW ZEALAND: Refer to  
the Note in Setup > Basic Setup, page 5 for  
setup instructions specific to your country.  
How to Access the Utility  
Launch the web browser on your computer, and enter the  
device’s default IP address, 192.168.1.1, in the Address  
field. Then, press Enter.  
A login screen appears. Use the default user name and  
password, admin, unless you changed them when you  
ran the Setup Wizard. (You can set a new user name and  
password from the Administration tab’s Management  
screen.) Click OK to continue.  
Login  
If you are unable to log in, press the Reset button on the  
back panel for at least 5 seconds, then wait for the device  
to reset and try again.  
Using the Utility  
Immediately after login, the Basic Setup screen appears.  
Near the top of the screen is a bar with selectable tabs.  
Use these tabs to navigate within the Utility. The primary  
tabs indicate the Utility’s main configuration categories.  
Each primary tab has one or more secondary tabs that  
provide access to the primary tab’s configuration screens.  
Primary Tabs  
Access  
Restrictions  
Applications &  
Gaming  
Setup Wireless Storage Security  
Administration Status  
Basic Setup Ethernet DDNS MAC Address Clone Advanced Routing  
Secondary Tabs  
Navigation Tabs  
To access a screen, click the appropriate primary tab,  
then click the appropriate secondary tab. The screen will  
appear, with its primary and secondary tabs highlighted.  
Wireless ADSL2+ Modem Router  
4
 
   
Advanced Configuration  
Chapter 3  
Setup > Advanced Routing  
Setup Tab  
The Advanced Routing screen allows you to configure the  
device’s advanced routing functions, such as operating  
mode, dynamic mode, and static routing.  
The Setup tab provides the device’s basic setup functions.  
For detailed information on the Setup tab, refer to the  
Utility’s online help pages.  
Wireless Tab  
Setup > Basic Setup  
The Wireless tab allows you to configure the device’s  
wireless functions.  
The Basic Setup screen allows you to change the device’s  
general settings. The following connection types  
(encapsulations) are available:  
For detailed information on the Wireless tab, refer to the  
Utility’s online help pages.  
RFC 2364 PPPoA  
RFC 2516 PPPoE  
RFC 2684 Routed  
IPoA  
RFC 2684 Bridged - Dynamic IP Address  
RFC 2684 Bridged - Static IP Address  
Bridge Mode Only  
Wireless > Basic Wireless Settings  
The Basic Wireless Settings screen allows you to set up a  
network with Wi-Fi Protected Setup™, change the radio  
band, select the network mode, change the wireless  
network name (SSID), change the wireless channel and  
disable the SSID broadcast.  
NOTE FOR USERS IN NEW ZEALAND: To set up  
the device, follow these instructions:  
Wireless > Wireless Security  
The Wireless Security screen allows you to configure the  
security of your wireless network(s). It allows you to select  
from a number of security modes, such as WPA2.  
1. Access the Setup > Basic Setup screen.  
2. Select RFC 2364 PPPoA from the  
Encapsulation drop-down menu.  
Wireless > Wireless MAC Filter  
The Wireless MAC Filter screen allows you to control (block  
or allow) Internet access by individual devices on your  
wireless network by specifying their MAC addresses.  
3. For the Virtual Circuit ID, enter 0 for the VPI  
and 100 for the VCI.  
4. Select VC for Multiplexing.  
5. Select Multimode from the DSL Modulation  
drop-down menu.  
Wireless > Advanced Wireless Settings  
The Advanced Wireless Settings screen allows you to  
6. Enter your User Name and Password details  
from your ISP.  
7. Click Save Settings.  
configure the device’s advanced wireless functions.  
Storage Tab (WAG320N Only)  
The Storage tab allows you to configure the settings for an  
optional external USB storage device, such as a flash drive  
or hard disk drive.  
Setup > Ethernet  
The Ethernet screen allows you to configure the device’s  
Ethernet settings. It also allows you to set up the first  
Ethernet port as a WAN port.  
For detailed information on the Storage tab, refer to the  
Utility’s online help pages.  
Setup > DDNS  
The DDNS screen allows you to assign a fixed host and  
domain name to a network computer that has been  
assigned a dynamic Internet IP address. This is useful  
when you are hosting your own website, FTP server, or  
other server behind the device.  
Storage > Disk Management  
The Disk Management screen displays information on an  
attached USB storage device, and allows you to perform  
basic management functions on the device. It also  
provides information on the attached USB disk, allows for  
a blank disk to be formatted, and enables safe removal of  
the attached disk.  
Setup > MAC Address Clone  
Some service providers require you to register a MAC  
address in order to access the Internet. The MAC Address  
Clone screen lets you use the MAC address of a device that  
has already been registered with your service provider, by  
copying that MAC address to the device.  
Storage > Shared Folder  
The Shared Folder screen allows you to manage the shared  
folders on an external USB storage device. A shared folder  
Wireless ADSL2+ Modem Router  
5
 
 
Advanced Configuration  
Chapter 3  
is a directory on the device that a user can access through  
the network.  
For detailed information on the Applications & Gaming  
tab, refer to the Utility’s online help pages.  
Storage > Administration  
Applications & Gaming > Single Port Forwarding  
The Administration screen allows you to configure basic  
storage settings and manage the device’s users.  
The Single Port Forwarding screen allows you to set up  
port forwarding for a single port. You should assign static  
IP addresses to the destination computers before you use  
this feature.  
Storage > Media Server  
The Media Server screen allows you to configure the  
device’s built-in media server, and to select the folders to  
scan for content.  
Applications & Gaming > Port Range Forwarding  
The Port Range Forwarding screen allows you to set up  
port forwarding for a range of ports. You should assign  
static IP addresses to the destination computers before  
you use this feature.  
Security Tab  
The Security tab allows you to enhance the security of  
your network.  
Applications & Gaming > Port Range Triggering  
For detailed information on the Security tab, refer to the  
Utility’s online help pages.  
The Port Range Triggering screen allows you to set up port  
triggering. When port triggering is configured, the device  
watches for specified port numbers in outgoing data.  
When a match is found, the device records the sending  
computer’s IP address so that when the requested data  
returns, it can be sent to the proper computer.  
Security > Firewall  
The Firewall screen allows you to configure a firewall that  
can filter out various types of unwanted traffic on the  
device’s local network.  
Applications & Gaming > DMZ  
Security > VPN Passthrough  
The DMZ screen allows you to expose one network user  
to the Internet for use of a special-purpose service such  
as Internet gaming or video conferencing. DMZ hosting  
forwards all the ports at the same time to one computer.  
You should assign static IP addresses to the destination  
computers before you use this feature.  
The VPN Passthrough screen allows you to configure the  
device’s VPN passthrough feature. This feature lets VPN  
tunnels using the IPSec, L2TP, or PPTP protocols to pass  
through the device’s firewall.  
Access Restrictions Tab  
The Access Restrictions tab allows you to configure  
the Internet access restrictions for each device in your  
network.  
Applications & Gaming > QoS  
The QoS screen allows you to specify priorities for different  
types of traffic. Lower priority traffic will be slowed down  
to allow greater throughput or less delay for high priority  
traffic.  
For detailed information on the Access Restrictions tab,  
refer to the Utility’s online help pages.  
Administration Tab  
The Administration tab allows you to configure the device’s  
administrative functions.  
Access Restrictions > Internet Access Policy  
The Internet Access Policy screen allows you to define  
policies that are used to block or allow specific kinds  
of Internet usage and traffic, such as Internet access,  
designated applications, websites, and inbound traffic  
during specific days and times, and for a specified list of  
devices in your network.  
For detailed information on the Administration tab, refer  
to the Utility’s online help pages.  
Administration > Management  
The Management screen allows you to manage specific  
functions for access and security.  
Applications & Gaming Tab  
The Applications & Gaming tab allows you to configure  
functions such as port forwarding and quality of service  
that may be necessary for special applications such as  
hosting web servers, ftp servers, and e-mail servers on on  
your network, or other specialized internet applications  
such as videoconferencing or online gaming.  
Wireless ADSL2+ Modem Router  
6
 
 
Advanced Configuration  
Chapter 3  
NOTE ON CISCO WEB ASSISTANT OPTION  
Status Tab  
The Status tab allows you to display status information.  
(not on all models): If you see an “error code  
404” message (indicating that you entered an  
invalid web address), the Cisco Web Assistant  
will appear and automatically run a search  
based on the keywords in the web address. This  
feature can be enabled or disabled from this  
screen.  
For detailed information on the Status tab, refer to the  
Utility’s online help pages.  
Status > Modem Router  
The Modem Router screen displays information about the  
device and its current settings. The on-screen information  
will vary depending on the Internet Connection Type you  
use.  
NOTE ON TREND MICRO OPTION (not on all  
models): Trend Micro ProtectLink Gateway  
is a hosted security service that stops spam  
and filters URLS to prevent unwanted content  
from passing through your router. The Email  
Protection is the hosted messaging security  
solution provided by Trend Micro InterScan  
Messaging Hosted Security (IMHS). This feature  
can be enabled or disabled from this screen.  
Status > Local Network  
The Local Network screen displays the status of your Local  
Area Network.  
Status > Wireless Network  
The Wireless Network screen displays some basic  
information about the wireless network of the device.  
Administration > Reporting  
The Reporting screen allows you to configure system event  
logging and to configure sending of e-mail alerts when a  
Denial of Service attack is detected.  
Status > DSL Connection  
The DSL Connection screen displays the status of your DSL  
connection.  
Administration > Diagnostics  
The Diagnostics screen allows you to perform a ping test  
to check the status of your Internet connection.  
Administration > Back Up & Restore  
The Back Up & Restore screen allows you to back up and  
restore the configuration settings of your device.  
Administration > Factory Defaults  
The Factory Defaults screen allows you to restore the  
factory defaults of the device. All savings you have saved  
will be lost  
NOTE: Restoring the factory defaults causes all  
settings you have previously saved to be lost.  
Administration > Firmware Upgrade  
The Firmware Upgrade screen allows you to upgrade the  
device’s firmware.  
Administration > Language  
The Language screen allows you to select an available  
language for the utility.  
Wireless ADSL2+ Modem Router  
7
 
 
Troubleshooting  
Appendix A  
You need to modify the basic settings on the  
deviceRouter.  
Appendix A:  
Troubleshooting  
Run the Setup Wizard on the Setup CD-ROM.  
You need to modify the advanced settings on the  
device.  
Your computer cannot connect to the Internet.  
Follow the instructions until your computer can connect  
to the Internet:  
Open the web browser (for example, Internet Explorer or  
Firefox), and enter the device’s IP address in the address  
field (the default IP address is 192.168.1.1). When  
prompted, complete the User name and Password fields  
(the default user name and password is admin). Click the  
appropriate tab to change the settings  
Make sure that the Modem Router is powered on. The  
Power LED should be green and not flashing.  
If the Power LED is flashing, then power off all of  
your network devices, including the Modem Router  
and computers. Then power on each device in the  
following order:  
WEB: If your questions are not  
addressed here, refer to the website,  
1. Modem Router  
2. Computer  
Check the LEDs on the device’s front panel. Make sure  
the Power, DSL, and at least one of the numbered  
Ethernet LEDs are lit. If they are not, then check  
the cable connections. The computer should be  
connected to one of the Ethernet ports numbered  
1-4 on the device, and the device’s DSL port must be  
connected to the ADSL line.  
When you double-click the web browser, you are  
prompted for a user name and password. If you want to  
get rid of the prompt, follow these instructions.  
Launch the web browser and perform the following steps  
(these steps are specific to Internet Explorer but are similar  
for other browsers):  
1. Select Tools > Internet Options.  
2. Click the Connections tab.  
3. Select Never dial a connection.  
4. Click OK.  
You are using a static IP address and cannot connect.  
Refer to Windows Help and change your Internet Protocol  
(TCP/IP) Properties to Obtain an IP address automatically.  
The computer cannot connect wirelessly to the network.  
Make sure the wireless network name or SSID is the same  
on both the computer and the device. If you have enabled  
wireless security, then make sure the same security  
method and key are used by both the computer and the  
device.  
Wireless ADSL2+ Modem Router  
8
 
 
Specifications  
Appendix B  
Operating Temp. 0 to 40°C (32 to 104°F)  
Appendix B:  
Storage Temp.  
-20 to 70°C (-4 to 158°F)  
Operating  
Humidity  
Specifications  
10 to 85% Noncondensing  
Storage Humidity 5 to 90% Noncondensing  
WAG120N  
Standards  
WAG160N v2  
WLAN: 802.11n draft 2.0, 802.11g,  
802.11b  
Standards  
WLAN: 802.11n draft 2.0, 802.11g,  
802.11b  
Ethernet: 802.3, 802.3u  
ADSL: T1.413i2, G.992.1 (G.DMT),  
G.992.2 (G.Lite), G.992.3 (ADSL2),  
G.992.5 (ADSL2+) for Annex A, B, M, L,  
U-R2 for Annex B  
Ethernet: 802.3, 802.3u  
ADSL: T1.413i2, G.992.1 (G.DMT),  
G.992.2 (G.Lite), G.992.3 (ADSL2),  
G.992.5 (ADSL2+) for Annex A, B, M, L,  
U-R2 for Annex B  
Ports  
DSL, Ethernet (1-4), Power  
Buttons  
LEDs  
On/Off, Reset, Wi-Fi Protected Setup™  
Ports  
Power, DSL, Ethernet (1-4)  
Power, Ethernet (1-4), Security,  
Wireless, DSL, Internet  
Buttons  
LEDs  
On/Off, Reset, Wi-Fi Protected Setup™  
Power, Ethernet (1-4), Ethernet WAN,  
Security, Wireless, DSL, Internet  
Cabling Type  
CAT5, RJ-11 (for Annex A),  
RJ-45 (for Annex B)  
Cabling Type  
CAT5, RJ-11 (for Annex A),  
RJ-45 (for Annex B)  
Antennas  
2 Internal  
Modulations  
802.11b: CCK/QPSK, BPSK  
Antennas  
2 Internal  
802.11g: OFDM/BPSK, QPSK, 16-QAM,  
64-QAM  
Modulations  
802.11b: CCK/QPSK, BPSK  
802.11g: OFDM/BPSK, QPSK, 16-QAM,  
64-QAM  
802.11n: OFDM/BPSK, QPSK, 16-QAM,  
64-QAM  
802.11n: OFDM/BPSK, QPSK, 16-QAM,  
64-QAM  
Transmit Power  
802.11b: 17,0 1,0 dBm  
802.11g: 15,0 1,0 dBm  
802.11n: 13,0 1,5 dBm  
Transmit Power  
802.11b: 17,0 1,0 dBm  
802.11g: 15,0 1,0 dBm  
802.11n: 13,0 1,5 dBm  
Receive Sensitivity -80 dBm (typical) @ 11 Mbps  
-70 dBm (typical) @ 54 Mbps  
Receive Sensitivity -80 dBm (typical) @ 11 Mbps  
-72 dBm (typical) @ 54 Mbps  
-61 dBm (typical) @ 130 Mbps  
-61 dBm (typical) @ 270 Mbps  
-66 dBm (typical) @ 130 Mbps  
-63 dBm (typical) @ 270 Mbps  
Antenna Gain  
1,8 dBi  
Security Features WPA2/WPAPersonal and Enterprise;  
Antenna Gain  
2 dBi  
128, 64 bits WEP;  
MAC Address Filtering;  
SPI Firewall  
Security Features WPA2/WPAPersonal and Enterprise  
;
128, 64 bits WEP;  
MAC Address Filtering;  
SPI Firewall  
OS Requirements Windows XP, Vista, or Vista 64-bit  
(to run the  
Setup CD)  
edition with latest updates (for  
Network Magic and Setup Wizard);  
Mac OS X 10.4 or higher (for Setup  
Wizard)  
OS Requirements Windows XP, Vista, or Vista 64-bit  
(to run the  
Setup CD)  
edition with latest updates (for  
Network Magic and Setup Wizard);  
Mac OS X 10.4 or higher (for Setup  
Wizard)  
Environmental  
Dimensions  
Weight  
202 x 34 x 160 mm (8,0” x 1,3” x 6,3”)  
362 g (12,8 oz)  
Environmental  
Dimensions  
Weight  
202 x 34 x 160 mm (8,0" x 1,3" x 6,3")  
362 g (12,8 oz)  
Power  
12VDC, 1A  
Certification  
FCC, CE, Telepermit, K.21, UL, CB,  
Wi-Fi (802.11b/g), WPA, WPA2,  
WMM, Wi-Fi Protected Setup™  
Power  
12VDC, 1A  
Certification  
FCC, CE, Wi-Fi®, A-Tick,Telepermit,  
WPA, WPA2™  
Wireless ADSL2+ Modem Router  
9
 
 
Specifications  
Appendix B  
Operating Temp. 0 to 40°C (32 to 104°F)  
5 GHz:  
RIFA 1 & RIFA 2 & RIFA 3 ≤ 3,5 dBi  
(Typical)  
Storage Temp.  
-20 to 70°C (-4 to 158°F)  
Operating  
Humidity  
Security Features WPA2/WPAPersonal and Enterprise  
;
10 to 85% Noncondensing  
128, 64 bits WEP;  
MAC Address Filtering;  
SPI Firewall  
Storage Humidity 5 to 90% Noncondensing  
WAG320N  
Standards  
OS Requirements Windows XP, Vista, or Vista 64-bit  
WLAN: 802.11n draft 2.0, 802.11g,  
802.11b, 802.11a  
(to run the  
Setup CD)  
edition with latest updates (for  
Network Magic and Setup Wizard);  
Mac OS X 10.4 or higher (for Setup  
Wizard)  
Ethernet: 802.3, 802.3u, 802.3ab  
ADSL: T1.413i2, G.992.1 (G.DMT),  
G.992.2 (G.Lite), G.992.3 (ADSL2),  
G.992.5 (ADSL2+) for Annex A, M, L,  
Environmental  
Dimensions  
202 x 34 x 160 mm  
(8,0" x 1,3" x 6,3")  
Ports  
Power, DSL, Ethernet (1-4), USB  
Weight  
362 g (12,8 oz)  
12VDC, 1,25A  
Buttons  
LEDs  
On/Off, Reset, Wi-Fi Protected Setup™  
Power  
Power, Ethernet (1-4), Ethernet WAN,  
Security, USB, Wireless, DSL, Internet  
Certification  
FCC, CE, Wi-Fi®, A-Tick,Telepermit,  
WPA, WPA2™  
Cabling Type  
Antennas  
CAT5, RJ-11 (for Annex A)  
3 Internal  
Operating Temp. 0 to 40°C (32 to 104°F)  
Storage Temp.  
-20 to 70°C (-4 to 158°F)  
Modulations  
802.11a: OFDM/BPSK, QPSK, 16-QAM,  
64-QAM  
Operating  
Humidity  
10 to 85% Noncondensing  
802.11b: CCK/QPSK, BPSK  
Storage Humidity 5 to 90% Noncondensing  
802.11g: OFDM/BPSK, QPSK, 16-QAM,  
64-QAM  
802.11n: OFDM/BPSK, QPSK, 16-QAM,  
64-QAM  
Transmit Power  
2,4 GHz:  
802.11b: 17,5 1,5 dBm Typical @  
Normal Temp. Range  
802.11g: 17,5 1,5 dBm Typical @  
Normal Temp. Range  
Wireless-N 20 MHz: 13,5 1,5 dBm  
Typical @ Normal Temp. Range  
Wireless-N 40 MHz: 13,5 1,5 dBm  
Typical @ Normal Temp. Range  
5 GHz:  
802.11a: 13,5 1,5 dBm Typical @  
Normal Temp. Range  
Wireless-N 20 MHz: 13,5 1,5 dBm  
Typical @ Normal Temp. Range  
Wireless-N 40 MHz: 13,5 1,5 dBm  
Typical @ Normal Temp. Range  
Receive Sensitivity -80 dBm (typical) @ 11 Mbps  
-72 dBm (typical) @ 54 Mbps  
-66 dBm (typical) @ 130 Mbps  
-63 dBm (typical) @ 270 Mbps  
Antenna Gain  
2,4 GHz:  
RIFA 1 & RIFA 2 & RIFA 3 ≤ 4 dBi  
(Typical)  
Wireless ADSL2+ Modem Router  
10  
 
 
Regulatory Information  
Appendix C  
Appendix C:  
Regulatory Information  
Þetta tæki er samkvæmt grunnkröfum og  
öðrum viðeigandi ákvæðum Tilskipunar  
1999/5/EC.  
Íslenska  
[Icelandic]:  
Questo apparato  
é
conforme ai requisiti  
Italiano  
[Italian]:  
essenziali ed agli altri principi sanciti dalla  
Direttiva 1999/5/CE.  
European Union  
The following information applies if you use the product  
within the European Union.  
Šī iekārta atbilst Direktīvas 1999/5/  
EK būtiskajām prasībām un citiem ar to  
saistītajiem noteikumiem.  
Latviski  
[Latvian]:  
Declaration of Conformity with Regard to EU  
Directive 1999/5/EC (R&TTE Directive)  
Compliance Information for 2,4-GHz and 5-GHz Wireless  
Products Relevant to the EU and Other Countries  
Following the EU Directive 1999/5/EC (R&TTE Directive)  
Šis įrenginys tenkina 1999/5/EB Direktyvos  
esminius reikalavimus ir kitas šios direktyvos  
nuostatas.  
Lietuvių  
[Lithuanian]:  
Dit apparaat voldoet aan de essentiele eisen  
en andere van toepassing zijnde bepalingen  
van de Richtlijn 1999/5/EC.  
Nederlands  
[Dutch]:  
NOTE: The 5 GHz information does not apply to  
Wireless-G (802.11g) only products.  
Dan l-apparat huwa konformi mal-ħtiġiet  
essenzjali u l-provedimenti l-oħra rilevanti  
tad-Direttiva 1999/5/EC.  
Malti  
[Maltese]:  
Това оборудване отговаря на съществените  
Б ъ л г а р с к и  
изисквания  
и
приложими клаузи на  
[Bulgarian]  
Ez  
a
készülék teljesíti az alapvető  
Директива 1999/5/ЕС.  
Magyar  
[Hungarian]:  
követelményeket  
irányelvben  
és  
más  
1999/5/EK  
vonatkozó  
meghatározott  
Toto zařízení je  
požadavky  
ustanoveními Směrnice 1999/5/EC.  
v
souladu se základními  
Česky  
[Czech]:  
rendelkezéseket.  
a
ostatními odpovídajícími  
Dette utstyret er  
i
samsvar med de  
Norsk  
[Norwegian]:  
grunnleggende krav og andre relevante  
bestemmelser i EU-direktiv 1999/5/EF.  
Dette udstyr er i overensstemmelse med  
de væsentlige krav og andre relevante  
bestemmelser i Direktiv 1999/5/EF.  
Dansk  
[Danish]:  
Urządzenie jest zgodne  
z
ogólnymi  
Polski  
[Polish]:  
wymaganiami oraz szczególnymi warunkami  
określonymi Dyrektywą UE: 1999/5/EC.  
Dieses Gerät entspricht den grundlegenden  
Deutsch  
Anforderungen  
und  
den  
weiteren  
entsprechenden Vorgaben der Richtlinie  
1999/5/EU.  
[German]:  
Este equipamento está em conformidade com  
os requisitos essenciais e outras provisões  
relevantes da Directiva 1999/5/EC.  
Português  
[Portuguese]:  
See seade vastab direktiivi 1999/5/EÜ  
olulistele nõuetele ja teistele asjakohastele  
sätetele.  
Eesti  
[Estonian]:  
Acest echipament este in conformitate  
cu cerintele esentiale si cu alte prevederi  
relevante ale Directivei 1999/5/EC.  
Română  
[Romanian]  
This equipment is in compliance with the  
essential requirements and other relevant  
provisions of Directive 1999/5/EC.  
English:  
Ta naprava je skladna z bistvenimi zahtevami  
in ostalimi relevantnimi pogoji Direktive  
1999/5/EC.  
Slovensko  
[Slovenian]:  
Este equipo cumple con los requisitos  
esenciales asi como con otras disposiciones  
de la Directiva 1999/5/CE.  
Español  
[Spanish]:  
Toto zariadenie je v zhode so základnými  
Slovensky  
[Slovak]:  
požiadavkami  
a
inými  
príslušnými  
nariadeniami direktív: 1999/5/EC.  
Αυτός ο εξοπλισµός είναι σε συµµόρφωση µε  
τις ουσιώδεις απαιτήσεις και άλλες σχετικές  
διατάξεις της Οδηγίας 1999/5/EC.  
Ελληνική  
[Greek]:  
Tämä laite täyttää direktiivin 1999/5/EY  
olennaiset vaatimukset ja on siinä asetettujen  
muiden laitetta koskevien määräysten  
mukainen.  
Suomi  
[Finnish]:  
Cet appareil est conforme aux exigences  
essentielles et aux autres dispositions  
pertinentes de la Directive 1999/5/EC.  
Français  
[French]:  
Denna utrustning är i överensstämmelse med  
de väsentliga kraven och andra relevanta  
bestämmelser i Direktiv 1999/5/EC.  
Svenska  
[Swedish]:  
Wireless ADSL2+ Modem Router  
11  
 
 
Regulatory Information  
Appendix C  
For all products, the Declaration of Conformity (DofC) is  
available through one or more of these options:  
nessuna limitazione, eccetto per i paesi menzionati di  
seguito:  
Das Produkt kann in allen EU Staaten ohne Einschränkungen  
eingesetzt werden (sowie in anderen Staaten die der EU  
Direktive 1999/5/CE folgen) mit Außnahme der folgenden  
aufgeführten Staaten:  
A pdf file is included on the product’s CD.  
A print copy is included with the product.  
A pdf file is available on the product’s webpage.  
select your country or region.Then select your product.  
In the majority of the EU and other European countries,  
the 2,4- and 5-GHz bands have been made available for  
the use of wireless local area networks (LANs). Later in  
this document you will find an overview of countries in  
which additional restrictions or requirements or both are  
applicable.  
If you need any other technical documentation, see the  
internationalsection, as shown later in this appendix.  
Non-Wireless Equipment (ADSL Modems/Gateways)  
The requirements for any country may evolve. Linksys  
recommends that you check with the local authorities for  
the latest status of their national regulations for both the  
2,4- and 5-GHz wireless LANs.  
The following standards were applied during the  
assessment of the product against the requirements of  
the Directive 1999/5/EC:  
EMC: EN 55 022 and EN 55 024  
Safety: EN 60950-1  
The following countries have restrictions and/or  
requirements in addition to those given in the table  
labeled “Overview of Regulatory Requirements for Wireless  
LANs”:  
CE Marking  
For the Linksys products such as the ADSL modems/  
gateways, the following CE mark is added to the  
equipment.  
Denmark  
In Denmark, the band 5150 - 5350 MHz is also allowed for  
outdoor usage.  
I Danmark må frekvensbåndet 5150 - 5350 også anvendes  
udendørs.  
France  
Wireless Equipment (Wireless-N/G/A/B Products)  
For 2,4 GHz, the product should not be used outdoors  
in the band 2454 - 2483,5 MHz. There are no restrictions  
when used in other parts of the 2,4 GHz band OR when  
used indoors. Check http://www.arcep.fr/ for more  
details.  
The following standards were applied during the  
assessment of the product against the requirements of  
the Directive 1999/5/EC:  
Radio: EN 300 328 and/or EN 301 893 as applicable  
EMC: EN 301 489-1, EN 301 489-17  
Pour la bande 2,4 GHz, l’ équipement ne doit pas être  
utilisé en extérieur dans la bande 2454- 2483,5 MHz. Il  
n’y a aucune restriction pour son utilisation dans d’autres  
parties de la bande des 2,4 GHz ainsi que pour une  
utilisation en intérieur. Consultez http://www.arcep.fr/  
pour de plus amples détails.  
Safety: EN 60950-1 and either EN 50385 or EN 50371  
For the Linksys Wireless-N, -G, -B, and/or -A products, the  
following CE mark, and class 2 identifier are added to the  
equipment.  
Italy  
This product meets the National Radio Interface and  
the requirements specified in the National Frequency  
Allocation Table for Italy. Unless this 2,4-GHz wireless LAN  
product is operating within the boundaries of the owner’s  
property, its use requires a “general authorization.  
Bands 5150-5350 MHz and 5470-5725 MHz require  
general authorization if used outdoors. Please check  
National Restrictions  
This product may be used in all EU countries (and other  
countries following the EU directive 1999/5/EC) without  
any limitation except for the countries mentioned below:  
Ce produit peut être utilisé dans tous les pays de l’UE (et dans  
tous les pays ayant transposés la directive 1999/5/CE) sans  
aucune limitation, excepté pour les pays mentionnés ci-  
dessous:  
Questo prodotto è conforme alla specifiche di Interfaccia  
Radio Nazionali e rispetta il Piano Nazionale di ripartizione  
delle frequenze in Italia. Se non viene installato all’interno  
del proprio fondo, l’utilizzo di prodotti Wireless LAN a  
Questo prodotto è utilizzabile in tutte i paesi EU (ed in tutti  
gli altri paesi che seguono le direttive EU 1999/5/EC) senza  
Wireless ADSL2+ Modem Router  
12  
 
Regulatory Information  
Appendix C  
2,4 GHz richiede una “Autorizzazione Generale. Lutilizzo  
all’aperto delle bande di frequenza 5150-5350 MHz e  
5470-5725 MHz è soggetto ad autorizzazione generale.  
Third-Party Software or Firmware  
The use of software or firmware not supported/provided  
by Linksys may result that the equipment is no longer  
compliant with the regulatory requirements.  
Consultare  
per  
maggiori dettagli.  
Technical Documents on  
Latvia  
Follow these steps to access technical documents:  
The outdoor usage of the 2,4 GHz band requires an  
authorization from the Electronic Communications Office.  
Please check http://www.esd.lv for more details.  
2,4 GHz frekveču joslas izmantošanai ārpus telpām  
nepieciešama atļauja no Elektronisko sakaru direkcijas.  
in your web browser.  
2. Select the country or region in which you live.  
3. Click the Products tab.  
Vairāk informācijas: http://www.esd.lv.  
Notes:  
4. Select the appropriate product category.  
5. Select the product sub-category, if necessary.  
6. Select the product.  
1. Although Norway, Switzerland and Liechtenstein are  
not EU member states, the EU Directive 1999/5/EC has  
also been implemented in those countries.  
7. Select the type of documentation you want from the More  
Information section.The document will open in PDF format  
if you have Adobe Acrobat installed on your computer.  
2. The regulatory limits for maximum output power are  
specified in EIRP. The EIRP level (in dBm) of a device can  
be calculated by adding the gain of the antenna used  
(specified in dBi) to the output power available at the  
connector (specified in dBm).  
NOTE: If you have questions regarding  
the compliance of this product or you  
cannot find the information you need,  
please contact your local sales office or visit  
Product Usage Restrictions  
This product is designed for indoor usage only. Outdoor  
usage is not recommended, unless otherwise noted.  
Outdoor usage may even be prohibited (see below).  
2,4 GHz Restrictions  
This product is designed for use with the standard, integral  
or dedicated (external) antenna(s) that is/are shipped  
together with the equipment. However, some applications  
may require the antenna(s), if removable, to be separated  
from the product and installed remotely from the device  
by using extension cables. For these applications, Linksys  
offers an R SMA extension cable (AC9SMA) and an R-TNC  
extension cable (AC9TNC). Both of these cables are 9  
meters long and have a cable loss (attenuation) of 5 dB. To  
compensate for the attenuation, Linksys also offers higher  
gain antennas, the HGA7S (with R-SMA connector) and  
HGA7T (with R-TNC connector). These antennas have a  
gain of 7 dBi and may only be used with either the R-SMA  
or R-TNC extension cable.  
Combinations of extension cables and antennas resulting  
in a radiated power level exceeding 20 dBm (100 mW)  
EIRP (2,4 GHz band) are illegal.  
5 GHz Restrictions  
Products that operate in any frequency within 5150 to  
5350 MHz are restricted to indoor use only, in all European  
countries except Denmark.  
Wireless ADSL2+ Modem Router  
13  
 
Regulatory Information  
Appendix C  
Čeština (Czech) - Informace o ochraně životního  
prostředí pro zákazníky v zemích Evropské unie  
User Information for Consumer Products Covered  
by EU Directive 2002/96/EC on Waste Electric and  
Electronic Equipment (WEEE)  
This document contains important information for users  
with regards to the proper disposal and recycling of  
Linksys products. Consumers are required to comply  
with this notice for all electronic products bearing the  
following symbol:  
Evropská směrnice 2002/96/ES zakazuje, aby zařízení označené  
tímto symbolem na produktu anebo na obalu bylo likvidováno  
s netříděným komunálním odpadem. Tento symbol udává,  
že daný produkt musí být likvidován odděleně od běžného  
komunálního odpadu. Odpovídáte za likvidaci tohoto produktu  
a dalších elektrických a elektronických zařízení prostřednictvím  
určených sběrných míst stanovených vládou nebo místními  
úřady. Správná likvidace  
a
recyklace pomáhá předcházet  
potenciálním negativním dopadům na životní prostředí a lidské  
zdraví. Podrobnější informace o likvidaci starého vybavení si  
laskavě vyžádejte od místních úřadů, podniku zabývajícího se  
likvidací komunálních odpadů nebo obchodu, kde jste produkt  
zakoupili.  
Dansk (Danish) - Miljøinformation for kunder i EU  
EU-direktiv 2002/96/EF kræver, at udstyr der bærer dette symbol  
på produktet og/eller emballagen ikke må bortskaffes som  
usorteret kommunalt affald. Symbolet betyder, at dette produkt  
skal bortskaffes adskilt fra det almindelige husholdningsaffald.  
Det er dit ansvar at bortskaffe dette og andet elektrisk og  
elektronisk udstyr via bestemte indsamlingssteder udpeget  
af staten eller de lokale myndigheder. Korrekt bortskaffelse  
og genvinding vil hjælpe med til at undgå mulige skader for  
miljøet og menneskers sundhed. Kontakt venligst de lokale  
myndigheder, renovationstjenesten eller den butik, hvor du  
har købt produktet, angående mere detaljeret information om  
bortskaffelse af dit gamle udstyr.  
English - Environmental Information for Customers in  
the European Union  
European Directive 2002/96/EC requires that the equipment  
bearing this symbol on the product and/or its packaging must  
not be disposed of with unsorted municipal waste. The symbol  
indicates that this product should be disposed of separately  
from regular household waste streams. It is your responsibility to  
dispose of this and other electric and electronic equipment via  
designated collection facilities appointed by the government or  
local authorities. Correct disposal and recycling will help prevent  
potential negative consequences to the environment and  
human health. For more detailed information about the disposal  
of your old equipment, please contact your local authorities,  
waste disposal service, or the shop where you purchased the  
product.  
Deutsch (German) - Umweltinformation für Kunden  
innerhalb der Europäischen Union  
Die Europäische Richtlinie 2002/96/EC verlangt, dass technische  
Ausrüstung, die direkt am Gerät und/oder an derVerpackung mit  
diesem Symbol versehen ist , nicht zusammen mit unsortiertem  
Gemeindeabfall entsorgt werden darf. Das Symbol weist darauf  
hin, dass das Produkt von regulärem Haushaltmüll getrennt  
entsorgt werden sollte. Es liegt in Ihrer Verantwortung, dieses  
Gerät und andere elektrische und elektronische Geräte über  
die dafür zuständigen und von der Regierung oder örtlichen  
Behörden dazu bestimmten Sammelstellen zu entsorgen.  
Ordnungsgemäßes Entsorgen und Recyceln trägt dazu bei,  
potentielle negative Folgen für Umwelt und die menschliche  
Gesundheit zu vermeiden. Wenn Sie weitere Informationen zur  
Entsorgung Ihrer Altgeräte benötigen, wenden Sie sich bitte an  
die örtlichen Behörden oder städtischen Entsorgungsdienste  
oder an den Händler, bei dem Sie das Produkt erworben haben.  
Български (Bulgarian)  
-
Информация относно  
опазването на околната среда за потребители в  
Европейския съюз  
Европейска директива 2002/96/EC изисква уредите, носещи  
този символ върху изделието и/или опаковката му, да не  
се изхвърля т с несортирани битови отпадъци. Символът  
обозначава, че изделието трябва да се изхвърля отделно от  
сметосъбирането на обикновените битови отпадъци. Ваша  
е отговорността този и другите електрически и електронни  
уреди да се изхвърлят в предварително определени от  
държавните или общински органи специализирани пунктове  
за събиране. Правилното изхвърляне  
и
рециклиране  
ще спомогнат да се предотвратят евентуални вредни за  
околната среда и здравето на населението последствия. За  
по-подробна информация относно изхвърлянето на вашите  
стари уреди се обърнете към местните власти, службите за  
сметосъбиране или магазина, от който сте закупили уреда.  
Wireless ADSL2+ Modem Router  
14  
 
Regulatory Information  
Appendix C  
Eesti (Estonian)  
Euroopa Liidus asuvatele klientidele  
-
Keskkonnaalane informatsioon  
Français (French) - Informations environnementales  
pour les clients de l’Union européenne  
Euroopa Liidu direktiivi 2002/96/EÜ nõuete kohaselt on  
La directive européenne 2002/96/CE exige que l’équipement  
sur lequel est apposé ce symbole sur le produit et/ou son  
emballage ne soit pas jeté avec les autres ordures ménagères. Ce  
symbole indique que le produit doit être éliminé dans un circuit  
distinct de celui pour les déchets des ménages. Il est de votre  
responsabilité de jeter ce matériel ainsi que tout autre matériel  
électrique ou électronique par les moyens de collecte indiqués  
par le gouvernement et les pouvoirs publics des collectivités  
territoriales. L’élimination et le recyclage en bonne et due forme  
ont pour but de lutter contre l’impact néfaste potentiel de ce  
type de produits sur l’environnement et la santé publique. Pour  
plus d’informations sur le mode d’élimination de votre ancien  
équipement, veuillez prendre contact avec les pouvoirs publics  
locaux, le service de traitement des déchets, ou l’endroit où vous  
avez acheté le produit.  
seadmeid, millel on tootel või pakendil käesolev sümbol  
,
keelatud kõrvaldada koos sorteerimata olmejäätmetega. See  
sümbol näitab, et toode tuleks kõrvaldada eraldi tavalistest  
olmejäätmevoogudest. Olete kohustatud kõrvaldama käesoleva  
ja ka muud elektri- ja elektroonikaseadmed riigi või kohalike  
ametiasutuste poolt ette nähtud kogumispunktide kaudu.  
Seadmete korrektne kõrvaldamine ja ringlussevõtt aitab vältida  
võimalikke negatiivseid tagajärgi keskkonnale ning inimeste  
tervisele. Vanade seadmete kõrvaldamise kohta täpsema  
informatsiooni saamiseks võtke palun ühendust kohalike  
ametiasutustega, jäätmekäitlusfirmaga või kauplusega, kust te  
toote ostsite.  
Español (Spanish) - Información medioambiental para  
clientes de la Unión Europea  
Italiano (Italian) - Informazioni relative all’ambiente  
per i clienti residenti nell’Unione Europea  
La direttiva europea 2002/96/EC richiede che le apparecchiature  
La Directiva 2002/96/CE de la UE exige que los equipos que  
lleven este símbolo en el propio aparato y/o en su embalaje  
no deben eliminarse junto con otros residuos urbanos no  
seleccionados. El símbolo indica que el producto en cuestión  
debe separarse de los residuos domésticos convencionales con  
vistas a su eliminación. Es responsabilidad suya desechar este y  
cualesquiera otros aparatos eléctricos y electrónicos a través de  
los puntos de recogida que ponen a su disposición el gobierno y  
lasautoridadeslocales. Aldesecharyreciclarcorrectamenteestos  
aparatos estará contribuyendo a evitar posibles consecuencias  
negativas para el medio ambiente y la salud de las personas. Si  
desea obtener información más detallada sobre la eliminación  
segura de su aparato usado, consulte a las autoridades locales,  
al servicio de recogida y eliminación de residuos de su zona o  
pregunte en la tienda donde adquirió el producto.  
contrassegnate con questo simbolo  
sul prodotto e/o  
sull’imballaggio non siano smaltite insieme ai rifiuti urbani  
non differenziati. Il simbolo indica che questo prodotto non  
deve essere smaltito insieme ai normali rifiuti domestici. È  
responsabilità del proprietario smaltire sia questi prodotti sia  
le altre apparecchiature elettriche ed elettroniche mediante  
le specifiche strutture di raccolta indicate dal governo o dagli  
enti pubblici locali. Il corretto smaltimento ed il riciclaggio  
aiuteranno a prevenire conseguenze potenzialmente negative  
per l’ambiente e per la salute dell’essere umano. Per ricevere  
informazioni più dettagliate circa lo smaltimento delle vecchie  
apparecchiature in Vostro possesso, Vi invitiamo a contattare gli  
enti pubblici di competenza, il servizio di smaltimento rifiuti o il  
negozio nel quale avete acquistato il prodotto.  
Ελληνικά (Greek)  
-
Στοιχεία περιβαλλοντικής  
προστασίας για πελάτες εντός της Ευρωπαϊκής  
Ένωσης  
Latviešu valoda (Latvian) - Ekoloģiska informācija  
klientiem Eiropas Savienības jurisdikcijā  
Σύμφωνα με την Κοινοτική Οδηγία 2002/96/EC, ο εξοπλισμός που  
φέρει αυτό το σύμβολο στο προϊόν ή/και τη συσκευασία του  
δεν πρέπει να απορρίπτεται μαζί με τα μη διαχωρισμένα αστικά  
απορρίμματα. Το σύμβολο υποδεικνύει ότι αυτό το προϊόν θα  
πρέπει να απορρίπτεται ξεχωριστά από τα συνήθη οικιακά  
απορρίμματα. Είστε υπεύθυνος για την απόρριψη του παρόντος  
και άλλου ηλεκτρικού και ηλεκτρονικού εξοπλισμού μέσω των  
καθορισμένων εγκαταστάσεων συγκέντρωσης απορριμμάτων,  
οι οποίες ορίζονται από το κράτος ή τις αρμόδιες τοπικές αρχές.  
Η σωστή απόρριψη και ανακύκλωση συμβάλλει στην πρόληψη  
ενδεχόμενων αρνητικών επιπτώσεων στο περιβάλλον και την  
υγεία. Για περισσότερες πληροφορίες σχετικά με την απόρριψη  
του παλαιού σας εξοπλισμού, επικοινωνήστε με τις τοπικές  
αρχές, τις υπηρεσίες αποκομιδής απορριμμάτων ή το κατάστημα  
από το οποίο αγοράσατε το προϊόν.  
Direktīvā 2002/96/EK ir prasība, ka aprīkojumu, kam pievienota  
zīme uz paša izstrādājuma vai uz tā iesaiņojuma, nedrīkst  
izmest nešķirotā veidā kopā ar komunālajiem atkritumiem  
(tiem, ko rada vietēji iedzīvotāji un uzņēmumi). Šī zīme nozīmē  
to, ka šī ierīce ir jāizmet atkritumos tā, lai tā nenonāktu kopā ar  
parastiem mājsaimniecības atkritumiem. Jūsu pienākums ir šo  
un citas elektriskas un elektroniskas ierīces izmest atkritumos,  
izmantojot īpašus atkritumu savākšanas veidus un līdzekļus, ko  
nodrošina valsts un pašvaldību iestādes. Ja izmešana atkritumos  
un pārstrāde tiek veikta pareizi, tad mazinās iespējamais  
kaitējums dabai un cilvēku veselībai. Sīkākas ziņas par  
novecojuša aprīkojuma izmešanu atkritumos jūs varat saņemt  
vietējā pašvaldībā, atkritumu savākšanas dienestā, kā arī veikalā,  
kur iegādājāties šo izstrādājumu.  
Wireless ADSL2+ Modem Router  
15  
 
Regulatory Information  
Appendix C  
Lietuvškai (Lithuanian) - Aplinkosaugos informacija,  
skirta Europos Sąjungos vartotojams  
Nederlands (Dutch) - Milieu-informatie voor klanten  
in de Europese Unie  
Europos direktyva 2002/96/EC numato, kad įrangos, kuri ir  
kurios pakuotė yra pažymėta šiuo simboliu (įveskite simbolį),  
negalima šalinti kartu su nerūšiuotomis komunalinėmis  
atliekomis. Šis simbolis rodo, kad gaminį reikia šalinti atskirai  
nuo bendro buitinių atliekų srauto. Jūs privalote užtikrinti, kad  
ši ir kita elektros ar elektroninė įranga būtų šalinama per tam  
tikras nacionalinės ar vietinės valdžios nustatytas atliekų rinkimo  
sistemas. Tinkamai šalinant ir perdirbant atliekas, bus išvengta  
galimos žalos aplinkai ir žmonių sveikatai. Daugiau informacijos  
apie jūsų senos įrangos šalinimą gali pateikti vietinės valdžios  
institucijos, atliekų šalinimo tarnybos arba parduotuvės, kuriose  
įsigijote tą gaminį.  
De Europese Richtlijn 2002/96/EC schrijft voor dat apparatuur die  
is voorzien van dit symbool op het product of de verpakking,  
niet mag worden ingezameld met niet-gescheiden huishoudelijk  
afval. Dit symbool geeft aan dat het product apart moet worden  
ingezameld. U bent zelf verantwoordelijk voor de vernietiging  
vandezeenandereelektrischeenelektronischeapparatuurviade  
daarvoor door de landelijke of plaatselijke overheid aangewezen  
inzamelingskanalen. De juiste vernietiging en recycling van  
deze apparatuur voorkomt mogelijke negatieve gevolgen voor  
het milieu en de gezondheid. Voor meer informatie over het  
vernietigen van uw oude apparatuur neemt u contact op met  
de plaatselijke autoriteiten of afvalverwerkingsdienst, of met de  
winkel waar u het product hebt aangeschaft.  
Malti (Maltese)  
Klijenti fl-Unjoni Ewropea  
-
Informazzjoni Ambjentali għal  
Norsk (Norwegian) - Miljøinformasjon for kunder i EU  
EU-direktiv 2002/96/EF krever at utstyr med følgende symbol  
avbildet på produktet og/eller pakningen, ikke må kastes  
sammen med usortert avfall. Symbolet indikerer at dette  
produktet skal håndteres atskilt fra ordinær avfallsinnsamling  
for husholdningsavfall. Det er ditt ansvar å kvitte deg med  
dette produktet og annet elektrisk og elektronisk avfall via egne  
innsamlingsordninger slik myndighetene eller kommunene  
bestemmer. Korrekt avfallshåndtering og gjenvinning vil  
være med på å forhindre mulige negative konsekvenser for  
miljø og helse. For nærmere informasjon om håndtering av  
det kasserte utstyret ditt, kan du ta kontakt med kommunen,  
en innsamlingsstasjon for avfall eller butikken der du kjøpte  
produktet.  
Id-Direttiva Ewropea 2002/96/KE titlob li t-tagħmir li jkun fih  
is-simbolu  
fuq il-prodott u/jew fuq l-ippakkjar ma jistax  
jintrema ma’ skart muniċipali li ma ġiex isseparat. Is-simbolu  
jindika li dan il-prodott għandu jintrema separatament minn ma’  
l-iskart domestiku regolari. Hija responsabbiltà tiegħek li tarmi  
dan it-tagħmir u kull tagħmir ieħor ta’ l-elettriku u elettroniku  
permezz ta’ faċilitajiet ta’ ġbir appuntati apposta mill-gvern jew  
mill-awtoritajiet lokali. Ir-rimi b’mod korrett u r-riċiklaġġ jgħin  
jipprevjeni konsegwenzi negattivi potenzjali għall-ambjent u  
għas-saħħa tal-bniedem. Għal aktar informazzjoni dettaljata  
dwar ir-rimi tat-tagħmir antik tiegħek, jekk jogħġbok ikkuntattja  
lill-awtoritajiet lokali tiegħek, is-servizzi għar-rimi ta’ l-iskart, jew  
il-ħanut minn fejn xtrajt il-prodott.  
Polski (Polish) - Informacja dla klientów w Unii  
Magyar (Hungarian) - Környezetvédelmi információ az  
európai uniós vásárlók számára  
Europejskiej  
środowiska  
o
przepisach dotyczących ochrony  
A
2002/96/EC számú európai uniós irányelv megkívánja,  
hogy azokat termékeket, amelyeken, és/vagy amelyek  
csomagolásán az alábbi címke megjelenik, tilos a többi  
a
Dyrektywa Europejska 2002/96/EC wymaga, aby sprzęt  
oznaczony symbolem znajdującym się na produkcie i/  
szelektálatlan lakossági hulladékkal együtt kidobni. A címke  
azt jelöli, hogy az adott termék kidobásakor a szokványos  
háztartási hulladékelszállítási rendszerektõl elkülönített eljárást  
kell alkalmazni. Az Ön felelõssége, hogy ezt, és más elektromos  
és elektronikus berendezéseit a kormányzati vagy a helyi  
hatóságok által kijelölt gyűjtõredszereken keresztül számolja  
fel. A megfelelõ hulladékfeldolgozás segít a környezetre és az  
emberi egészségre potenciálisan ártalmas negatív hatások  
megelõzésében. Ha elavult berendezéseinek felszámolásához  
további részletes információra van szüksége, kérjük, lépjen  
lub jego opakowaniu nie był wyrzucany razem z innymi  
niesortowanymi odpadami komunalnymi. Symbol ten wskazuje,  
że produkt nie powinien być usuwany razem ze zwykłymi  
odpadami z gospodarstw domowych. Na Państwu spoczywa  
obowiązek wyrzucania tego i innych urządzeń elektrycznych  
oraz elektronicznych  
przez władze krajowe lub lokalne. Pozbywanie się sprzętu  
we właściwy sposób jego recykling pomogą zapobiec  
w
punktach odbioru wyznaczonych  
i
potencjalnie negatywnym konsekwencjom dla środowiska i  
zdrowia ludzkiego. W celu uzyskania szczegółowych informacji  
o usuwaniu starego sprzętu, prosimy zwrócić się do lokalnych  
władz, służb oczyszczania miasta lub sklepu, w którym produkt  
został nabyty.  
kapcsolatba  
a
helyi hatóságokkal,  
a
hulladékfeldolgozási  
szolgálattal, vagy azzal üzlettel, ahol a terméket vásárolta.  
Wireless ADSL2+ Modem Router  
16  
 
Regulatory Information  
Appendix C  
Português (Portuguese) - Informação ambiental para  
clientes da União Europeia  
Slovenščina (Slovene)  
stranke v Evropski uniji  
-
Okoljske informacije za  
A Directiva Europeia 2002/96/CE exige que o equipamento  
que exibe este símbolo no produto e/ou na sua embalagem  
não seja eliminado junto com os resíduos municipais não  
Evropska direktiva 2002/96/ES prepoveduje odlaganje opreme s  
tem simbolom – na izdelku in/ali na embalaži z nesortiranimi  
komunalnimi odpadki. Ta simbol opozarja, da je treba izdelek  
zavreči ločeno od preostalih gospodinjskih odpadkov. Vaša  
odgovornost je, da to in preostalo električno in elektronsko  
opremo oddate na posebna zbirališča, ki jih določijo državne  
separados.  
O
símbolo indica que este produto deve ser  
eliminado separadamente dos resíduos domésticos regulares.  
É da sua responsabilidade eliminar este e qualquer outro  
equipamento eléctrico e electrónico através das instalações  
de recolha designadas pelas autoridades governamentais ou  
locais. A eliminação e reciclagem correctas ajudarão a prevenir  
as consequências negativas para o ambiente e para a saúde  
humana. Para obter informações mais detalhadas sobre a  
forma de eliminar o seu equipamento antigo, contacte as  
autoridades locais, os serviços de eliminação de resíduos ou o  
estabelecimento comercial onde adquiriu o produto.  
ustanove ali lokalne oblasti.  
S
pravilnim odlaganjem in  
recikliranjem boste preprečili morebitne škodljive vplive na  
okolje in zdravje ljudi. Če želite izvedeti več o odlaganju stare  
opreme, se obrnite na lokalne oblasti, odlagališče odpadkov ali  
trgovino, kjer ste izdelek kupili.  
Suomi (Finnish) - Ympäristöä koskevia tietoja EU-  
alueen asiakkaille  
EU-direktiivi 2002/96/EY edellyttää, että jos laitteistossa on tämä  
Română (Romanian) - Informaţii de mediu pentru  
clienţii din Uniunea Europeană  
symboli  
itse tuotteessa ja/tai sen pakkauksessa, laitteistoa  
ei saa hävittää lajittelemattoman yhdyskuntajätteen mukana.  
Symboli merkitsee sitä, että tämä tuote on hävitettävä erillään  
tavallisesta kotitalousjätteestä. Sinun vastuullasi on hävittää  
tämä elektroniikkatuote ja muut vastaavat elektroniikkatuotteet  
viemällä tuote tai tuotteet viranomaisten määräämään  
keräyspisteeseen. Laitteiston oikea hävittäminen estää  
mahdolliset kielteiset vaikutukset ympäristöön ja ihmisten  
terveyteen. Lisätietoja vanhan laitteiston oikeasta hävitystavasta  
saa paikallisilta viranomaisilta, jätteenhävityspalvelusta tai siitä  
myymälästä, josta ostit tuotteen.  
Directiva europeană 2002/96/CE impune ca echipamentele care  
prezintă acest simbol pe produs şi/sau pe ambalajul acestuia să  
nu fie casate împreună cu gunoiul menajer municipal. Simbolul  
indică faptul că acest produs trebuie să fie casat separat de  
gunoiul menajer obişnuit. Este responsabilitatea dvs. să casaţi  
acest produs şi alte echipamente electrice şi electronice prin  
intermediul unităţilor de colectare special desemnate de guvern  
sau de autorităţile locale. Casarea şi reciclarea corecte vor ajuta  
la prevenirea potenţialelor consecinţe negative asupra sănătăţii  
mediului şi a oamenilor. Pentru mai multe informaţii detaliate  
cu privire la casarea acestui echipament vechi, contactaţi  
autorităţile locale, serviciul de salubrizare sau magazinul de la  
care aţi achiziţionat produsul.  
Svenska (Swedish) - Miljöinformation för kunder i  
Europeiska unionen  
Det europeiska direktivet 2002/96/EC kräver att utrustning med  
denna symbol på produkten och/eller förpackningen inte får  
kastas med osorterat kommunalt avfall. Symbolen visar att denna  
produktbörkastasefterattdenavskiljtsfrånvanligthushållsavfall.  
Det faller på ditt ansvar att kasta denna och annan elektrisk och  
elektronisk utrustning på fastställda insamlingsplatser utsedda  
av regeringen eller lokala myndigheter. Korrekt kassering och  
återvinning skyddar mot eventuella negativa konsekvenser  
för miljön och personhälsa. För mer detaljerad information om  
kassering av din gamla utrustning kontaktar du dina lokala  
myndigheter, avfallshanteringen eller butiken där du köpte  
produkten.  
Slovenčina (Slovak) - Informácie o ochrane životného  
prostredia pre zákazníkov v Európskej únii  
Podľa európskej smernice 2002/96/ES zariadenie  
s
týmto  
symbolom  
likvidované spolu  
na produkte a/alebo jeho balení nesmie byť  
s
netriedeným komunálnym odpadom.  
Symbol znamená, že produkt by sa mal likvidovať oddelene  
od bežného odpadu z domácností. Je vašou povinnosťou  
likvidovať toto i ostatné elektrické a elektronické zariadenia  
prostredníctvom špecializovaných zberných zariadení určených  
vládou alebo miestnymi orgánmi. Správna likvidácia a recyklácia  
pomôže zabrániť prípadným negatívnym dopadom na životné  
prostredie a zdravie ľudí. Ak máte záujem o podrobnejšie  
informácie o likvidácii starého zariadenia, obráťte sa, prosím, na  
miestne orgány, organizácie zaoberajúce sa likvidáciou odpadov  
alebo obchod, v ktorom ste si produkt zakúpili.  
WEB: For additional information, please visit  
Wireless ADSL2+ Modem Router  
17  
 
Regulatory Information  
Appendix C  
Cisco-Linksys ADSL2+ Devices on Long Lines  
Australia  
ADSL2+ devices may not achieve the type ofhigh speed”  
operation expected when attached to a line that is longer  
than intended by the ITU-T Rec. G.996.1 ADSL standard  
i.e. >3 km of 0.4mm cable or a shorter cable length with  
several tails or multiples. If the device is installed in such  
conditions and does not give the expected “download”  
performance, then do not refer the matter to the Telecom  
Fault Service or ADSL Helpdesk.  
The following information applies if you use the product  
within Australia.  
Safety Notice  
WARNING: To ensure compliance with  
exposure limits to radiofrequency fields, the  
antenna of the device should be no closer than  
20 cm from the body during use.  
United States of America  
The following information applies if you use the product  
within the United States of America.  
New Zealand  
The following information applies if you use the product  
within New Zealand.  
FCC Statement  
Telepermit Statement  
This device complies with Part 15 of the FCC Rules.  
Operation is subject to the following two conditions: (1)  
Thisdevicemaynotcauseharmfulinterference, and(2)this  
device must accept any interference received, including  
interference that may cause undesired operation.  
The cabling between the phone port and the phone shall  
not exceed 100 metres.  
PTC200 General Warning  
The grant of a Telepermit for any item of terminal  
equipment indicates only that Telecom has accepted  
that the item complies with minimum conditions for  
connection to its network. It indicates no endorsement  
of the product by Telecom, nor does it provide any sort  
of warranty. Above all, it provides no assurance that any  
item will work correctly in all respects with another item  
of Telepermitted equipment of a different make or model,  
nor does it imply that any product is compatible with all of  
Telecom’s network services.  
This product has been tested and complies with the  
specifications for a Class B digital device, pursuant to Part  
15 of the FCC Rules. These limits are designed to provide  
reasonable protection against harmful interference in  
a residential installation. This equipment generates,  
uses, and can radiate radio frequency energy and, if not  
installed and used according to the instructions, may  
cause harmful interference to radio communications.  
However, there is no guarantee that interference will not  
occur in a particular installation. If this equipment does  
cause harmful interference to radio or television reception,  
which is found by turning the equipment off and on, the  
user is encouraged to try to correct the interference by  
one or more of the following measures:  
Wireless Connectivity Security on Cisco-Linksys  
ADSL2+ Devices  
Setting up the security of the wireless connection  
associated with ADSL2+ device is the user’s responsibility.  
Telecom will take no responsibility for charges made to  
user’s accounts due to poorly organized wireless security  
allowing unknown users to connect to the Internet via this  
device. Do not complain to the Telecom Fault Service or  
Jetstream Helpdesk should this occur.  
Reorient or relocate the receiving antenna  
Increase the separation between the equipment or  
devices  
Connect the equipment to an outlet other than the  
receiver’s  
Consult a dealer or an experienced radio/TV technician  
for assistance  
General Warning for Cisco-Linksys ADSL2+  
Devices and ADSL2+ Capability  
FCC Caution: Any changes or modifications not expressly  
approved by the party responsible for compliance could  
void the user’s authority to operate this equipment.  
This device has been tested and found suitable to connect  
to the Telecom ADSL2+ capability. This indicates only that  
Telecom has accepted that this device complies with the  
spectrum management plan for ADSL2+ on copper cable  
and with simple voiceband compatibility tests included  
in PTC273. It does not indicate that this device is fully  
compatible with all services accessed via the ADSL2+  
capability. Contact the supplier of the device when  
issues occur. Do not call the Telecom Fault Service or the  
Jetstream Helpdesk.  
FCC Radiation Exposure Statement  
This equipment complies with FCC radiation exposure limits  
set forth for an uncontrolled environment. This equipment  
should be installed and operated with minimum distance  
20cm between the radiator and your body.  
Wireless ADSL2+ Modem Router  
18  
 
 
Regulatory Information  
Appendix C  
This transmitter must not be co-located or operating in  
conjunction with any other antenna or transmitter. IEEE  
802.11b or 802.11g operation of this product in the USA is  
firmware-limited to channels 1 through 11.  
No repairs may be done by the customer. If trouble is  
experienced with this equipment, please contact your  
authorized support provider for repair and warranty  
information. If the trouble is causing harm to the  
telephone network, the telephone company may request  
you remove the equipment from the network until the  
problem is resolved. This equipment cannot be used on  
telephone company provided coin service. Connection to  
Party Line Service is subject to state tariffs.  
FCC Part 68 Statement  
This equipment complies with Part 68 of the FCC Rules. A  
label is attached to the equipment that contains, among  
other information, its FCC registration number and ringer  
equivalence number. If requested, this information must  
be provided to the telephone company.  
Safety Notices  
This equipment uses the following USOC Jack: RJ-11.  
WARNING: To reduce the risk of fire, use only  
No.26 AWG or larger telecommunication line  
cord.  
An FCC compliant telephone cord and modular plug  
is provided with this equipment. This equipment is  
designed to be connected to the telephone network or  
premises wiring using a compatible modular jack, which  
is FCC Part 68 compliant. Connection to the telephone  
network should be made by using the standard modular  
telephone jack.  
WARNING: Do not use this product near water,  
for example, in a wet basement or near a  
swimming pool.  
The REN is useful to determine the quantity of devices  
that may be connected to the telephone line and still have  
all of those devices ring when your telephone number is  
called. In most, but not all areas, the sum of RENs should  
not exceed 5. To be certain of the number of devices that  
may be connected to the line, as determined by the total  
RENs, contact the telephone company to determine the  
maximum REN for the calling area.  
WARNING: Avoid using this product during an  
electrical storm. There may be a remote risk of  
electric shock from lightning.  
WARNING: This equipment will be inoperable  
when main power fails.  
If this equipment causes harm to the telephone network,  
the telephone company may discontinue your service  
temporarily. If advance notice is not practical, the  
telephone company will notify the customer as soon as  
possible. Also, you will be advised of your right to file a  
complaint with the FCC if you believe it is necessary.  
WARNING: To ensure compliance with  
explosure limits to radiofrequency fields, the  
antenna of the device should be no closer than  
20 cm from the body during use.  
The telephone company may make changes in its  
facilities, equipment, operations, or procedures that could  
affect the operation of the equipment. If this happens, the  
telephone company will provide advance notice in order  
for you to make the necessary modifications in order to  
maintain uninterrupted service.  
In the event this equipment should fail to operate  
properly, disconnect the unit from the telephone line.  
Try using another FCC approved device in the same  
telephone jack. If the trouble persists, call the telephone  
company repair service bureau. If the trouble does not  
persist and appears to be with this unit, disconnect the  
unit from the telephone line and discontinue use of the  
unit until it is repaired. Please note that the telephone  
company may ask that you disconnect the equipment  
from the telephone network until the problem has been  
corrected or until you are sure that the equipment is not  
malfunctioning. The user must use the accessories and  
cables supplied by the manufacturer to get optimum  
performance from the product.  
Wireless ADSL2+ Modem Router  
19  
 
Regulatory Information  
Appendix C  
Avis d’Industrie Canada concernant l’exposition aux radio-  
fréquences :  
Canada  
The following information applies if you use the product  
within Canada.  
Ce matériel est conforme aux limites établies par IC  
en matière d’exposition aux radiofréquences dans un  
environnement non contrôlé. Ce matériel doit être installé  
et utilisé à une distance d’au moins 20 cm entre l’antenne  
et le corps de l’utilisateur.  
Industry Canada Statement  
This device complies with Industry Canada ICES-003 and  
RSS210 rules.  
L’émetteur ne doit pas être placé près d’une autre antenne  
ou d’un autre émetteur, ou fonctionner avec une autre  
antenne ou un autre émetteur.  
Operation is subject to the following two conditions:  
1. This device may not cause interference and  
2. This device must accept any interference, including  
interference that may cause undesired operation of  
the device. This device has been designed to operate  
with an antenna having a maximum gain of 2dBi.  
Antenna having a higher gain is strictly prohibited per  
regulations of Industry Canada. The required antenna  
impedance is 50 ohms.  
Wireless Disclaimer  
The maximum performance for wireless is derived from  
IEEE Standard 802.11 specifications. Actual performance  
can vary, including lower wireless network capacity,  
data throughput rate, range and coverage. Performance  
depends on many factors, conditions and variables,  
including distance from the access point, volume of  
network traffic, building materials and construction,  
operating system used, mix of wireless products used,  
interference and other adverse conditions.  
To reduce potential radio interference to other users,  
the antenna type and its gain should be so chosen  
that the EIRP is not more than required for successful  
communication.  
Industry Canada Radiation Exposure Statement:  
Avis de non-responsabilité concernant les appar-  
eils sans fil  
This equipment complies with IC radiation exposure limits  
set forth for an uncontrolled environment. This equipment  
should be installed and operated with minimum distance  
20cm between the radiator & your body.  
Les performances maximales pour les réseaux sans fil  
sont tirées des spécifications de la norme IEEE 802.11.  
Les performances réelles peuvent varier, notamment  
en fonction de la capacité du réseau sans fil, du débit  
de la transmission de données, de la portée et de la  
couverture. Les performances dépendent de facteurs,  
conditions et variables multiples, en particulier de la  
distance par rapport au point d’accès, du volume du trafic  
réseau, des matériaux utilisés dans le bâtiment et du  
type de construction, du système d’exploitation et de la  
combinaison de produits sans fil utilisés, des interférences  
et de toute autre condition défavorable.  
This transmitter must not be co-located or operating in  
conjunction with any other antenna or transmitter.  
Avis d’Industrie Canada  
Cet appareil est conforme aux normes NMB003 et RSS210  
d’Industrie Canada.  
Lutilisation de ce dispositif est autorisée seulement aux  
conditions suivantes :  
1. il ne doit pas produire de brouillage et  
2. il doit accepter tout brouillage radioélectrique reçu,  
mêmesicebrouillageestsusceptibledecompromettre  
le fonctionnement du dispositif. Le dispositif a été  
conçupourfonctionneravecuneantenneayantungain  
maximum de 2 dBi. Les règlements d’Industrie Canada  
interdisent strictement l’utilisation d’antennes dont le  
gain est supérieur à cette limite. L’impédance requise  
de l’antenne est de 50 ohms.  
Afin de réduire le risque d’interférence aux autres  
utilisateurs, le type d’antenne et son gain doivent  
être choisis de façon à ce que la puissance isotrope  
rayonnée équivalente (p.i.r.e.) ne soit pas supérieure  
au niveau requis pour obtenir une communication  
satisfaisante.  
3425-01414  
 
090605-10_20-10C-AI  
Wireless ADSL2+ Modem Router  
20  
 

LG Electronics Conference Phone AVS2400 User Manual
LG Electronics Washer WD 3243RHD User Manual
Linear TV Receiver 2031 User Manual
Lochinvar Water Heater RW 090 360 User Manual
Mackie Car Amplifier am4000 User Manual
Manitowoc Ice Air Compressor J 0600 User Manual
Marantz Cassette Player SD4050 User Manual
Maytag Refrigerator MFI2269VEA10 User Manual
McCulloch Lawn Mower M53 190AWFP User Manual
Melissa Styling Iron 635 094 User Manual