Linksys Network Card SPA400 User Manual

Linksys SPA400  
Trixbox Integration Guide  
Access Point – Connecting You & Your Customers.  
 
Step 3 – Set the SPA400 to a Fixed IP address  
Asterisk needs to access your SPA400, so it needs to be set to a  
fixed ip address. To do this: -  
Under Setup -> Basic Setup  
Select Fixed IP address and enter a valid fixed IP address for  
your network.  
Be sure to enter a DNS server, if you do not know enter the  
Telstra DNS server 139.130.4.5 – You can leave the secondary  
blank  
Set your time zone.  
Click Save Settings  
Restart System  
Sample Config – Use Address Valid For Your Network  
Check with the network administrator if unsure.  
Note the IP address in the Notes Section.  
 
Step 4 – Setup the SPA400 Voice Configuration.  
Open the SPA400 in your web browser using the new IP address.  
Select Setup->SPA9000 Interface.  
Enter SPA400 in the User ID:  
Leave SPA9000 on discover automatically  
No other changes should need to be made  
Click Save Settings (You Do Not Need To Restart)  
Screenshot of Setup -> SPA9000 Interface  
Select Setup -> Voice  
 
For Australia you need to change:-  
Impedance : 220 Ohms + (820 Ohms || 120nF)  
On-Hook speed : 26ms  
 
Step 5 – Configure Trixbox Trunk.  
Open your FreePBX interface: http://trixbox.ip/admin/  
Select Trunks -> Add SIP trunk  
Complete the form with the details below:  
----------------------------------------------------------------------  
Outbound Caller ID: Blank  
Never Override CallerID : Unticked  
Maximum Channels: (the number of pstn lines plugged into the  
SPA400)  
Dial Rules: Leave Empty  
Outbound Dial Prefix: Empty  
Trunk Name: SPA400 (Can be anything you wish)  
Peer Details:  
allow=ulaw  
canreinvite=no  
context=from-trunk  
dtmfmode=rfc2833  
host=x.x.x.x  
insecure=very  
type=friend  
user=SPA400  
USER Context: Leave Blank  
USER Details: Blank (Delete the default information)  
Register String:  
SPA400@x.x.x.x/SPA400  
-----------------------------------------------------------------------  
Note : x.x.x.x should be where you enter the IP address of the  
SPA400  
Click Submit Changes.  
 
Step 6 – Configure Outbound Route.  
You can now treat the SPA400 like any other trunk. To add an  
outbound router (eg, dial 9 to dial out the SPA400)  
Outbound Routes -> Add Route  
Route Name: SPA400PSTN (this can be anything)  
Route Password: Blank  
Emergency Dialing: Unticked  
Intra Company Route: Unticked  
Dial Patterns: 9|.  
Trunk Sequence: SPA400  
Click Submit Changes  
Step 7 – Configure Inbound Route.  
This will setup an inbound route for people who call the PSTN lines  
plugged into the SPA400.  
Setup -> Inbound Routes -> Add Incoming Route  
DID Number: SPA400 (case sensitive)  
Caller ID Number: Blank  
Zaptel Channel: Blank  
Fax Handling  
Leave as is  
Select the Destination  
Click Submit  
Click the Red “Apply Configuration Changes” to reload asterisk  
 
Complete:  
You should now be able to make and receive calls via your SPA400.  
Email [email protected] for further support if required.  
Congratulations  
Notes:  
SPA400 IP Address: _____________________________  
SPA400 Username: ______________________________  
SPA400 Password: ______________________________  
Number of Lines: _____  
Installed By: _______________________________  
Date: ______________________________  
 

KWC Outdoor Shower 26000540000 User Manual
Legacy Car Audio Car Video System LD63MU User Manual
Lennox Hearth Bluetooth Headset BT 320S User Manual
LG Electronics Air Conditioner LP6000ER User Manual
Linn Stereo Amplifier 500 Solo User Manual
Lowrance electronic GPS Receiver X96 User Manual
Magellan GPS Receiver 5390 User Manual
Magnavox CD Player MPC421 User Manual
McCulloch Trimmer MCT2027 User Manual
Metrologic Instruments Scanner MS2221 MS2222 User Manual